5分钟前 武汉莫诺转子服务介绍「螺耐斯」[螺耐斯10e361c]内容：管柱脱落是自由式管柱结构经常发生的一种现象，这是由于正常运转时转子旋转对定子产生的摩擦扭矩方向实际上是定子及油管的连接螺纹的卸扣方向，如果摩擦力矩大于油管扣的上扣扭矩，油管就脱扣。当尾管很重时，还会出现螺纹掳扣。当管柱脱落时，通过作业重新连接好就能恢复生产。如果未发生螺纹掳扣，可以采取对扣方式打捞，如果发生掳扣，必须下打捞工具进行打捞。Column shedding is a common phenomenon of free tube structure, which is due to the direction of rotation of the friction torque generated by the stator rotor during normal operation is actually a stator and tubing connection1 screw shackle direction, if the friction torque is greater than the pipe le on torque, oil pipe tripping. When the tail pipe is very heavy, there will also be a thread caption. When the pipe column falls off, the production can be restored by reco
nnecting the work. If the le is not threaded, it can be salvaged by the way of the le. If the le occurs, the fishing tool must be salvaged.
定转子过早磨损Premature wear of fixed rotor定转子过早磨损主要是由于定转子的间隙过小引起的。The premature wear of the fixed rotor is mainly caused by the small gap between the fixed rotor and the rotor.油管与抽油杆柱磨损Oil pipe and rod string wear油管与抽油杆柱磨损的原因一是因为井斜抽油杆贴在油管壁上引起的，可以通过加抽油杆扶正器使抽油杆柱居中来减轻或消除，另一个原因是定转子不同心及转子的偏心运动造成的，在定子以上加一节内径较大的回转筒即可避免。Tubing and sucker rod wear reason is because the deviation of sucker rod attached to the tubing wall caused by heating, pumping rod centralizer make the rod center to reduce or eliminate, another reason is caused by the eccentric motion of the rotor and the rotor are not concentric, avoid a day the diameter of rotary cylinder in the stator can be larger than.
Ｄ、限位器D, limiting device限位器为一个底部带限位板和流通通道的短节，接在定子的尾部，其作用是施工作业时给转子限位以防止下入过头而失去作用和杆柱脱落时防止杆柱掉入井底。The limiting device is a short section with bottom limit plate and distribution channel, which is co
nnected to the tail of the stator. Its function is to limit the rotor to the rotor during ctruction1, so as to prevent it from falling into the overhead and lose its function and prevent the rod from falling into the bottom when the rod string falls off.
单螺杆泵的使用方法:
单螺杆泵在发达国家已广泛使用，德国称“偏心转子泵”。由于其单螺杆泵在发达国家已广泛使用，德国称“偏心转子泵”。由于其优良的性能，在国内的应用范围也在迅速扩大。它的特点是对介质的适应性强、流量平稳、压力脉动小、自吸能力高，这是其它任何泵种所不能替代的。
单螺杆泵使用方法,螺杆泵使用注意事项：
1、启动螺杆泵前还得必须先确定螺杆泵的运转方向，单螺杆泵不能反转。
2、螺杆泵严禁在泵腔无液体的情况下空运转，必须在启动前由泵进口把液体注入泵体后再启动螺杆泵，以免空转磨损螺杆泵定子。
